Experimental Investigation of Foam Flooding Using Anionic and Nonionic Surfactants: A Screening Scenario to Assess the Effects of Salinity and pH on Foam Stability and Foam Height
Экспериментальное исследование заводнения пеной с использованием анионных и неионогенных поверхностно-активных веществ: скрининговый подход к оценке влияния минерализации и pH на стабильность и высоту пены
2022-04-19
SCID: 54.1/b77amxkc
Discuss with AI
anionic and nonionic surfactantsenhanced oil recoveryfoam floodingfoam stabilitysalinity and pH
Figures from the paper
Abstract (AI)
High Resolution Image Download MS PowerPoint Slide Gravity override and viscous fingering are inevitable in gas flooding for improving hydrocarbon production from petroleum reservoirs. Foam is used to regulate gas mobility and consequently improve sweep efficiency. In the enhanced oil recovery process, when the foam is introduced into the reservoir and exposed to the initial saline water saturation and pH condition, selection of the stable foam is crucial. Salinity and pH tolerance of generated foams are a unique concern in high salinity and pH variable reservoirs. NaOH and HCl are used for adjusting the pH, and NaCl and CaCl 2 are utilized to change salinity. Through analyzing these two factors along with surfactant concentration, we have instituted a screening scenario to optimize the effects of salinity, pH, surfactant type, and concentration to generate the most stable state of the generated foams. An anionic (sodium dodecyl sulfate) and a nonionic (lauric alcohol ethoxylate-7) surfactants were utilized to investigate the effects of the surfactant type. The results were applied in a 40 cm synthetic porous media fully saturated with distilled water to illustrate their effects on water recovery at ambient conditions. This most stable foam along with eight different stabilities and foamabilities and air alone was injected into the sand pack. The results show that in optimum surfactant concentration, the stability of LA-7 was not highly changed with salinity alteration. Also, we probed that serious effects on foam stability are due to divalent salt and CaCl 2 . Finally, we found the most water recovery that was obtained by the three most stable foams by the formula of 1 cmc SDS + 0.5 M NaCl, 1 cmc SDS + 0.01 M CaCl 2, and LA-7@ pH ∼ 6 from porous media flooding. Total water recovery for the most stable foam increased by an amount of 65% compared to the state of air alone. A good correlation between foam stability and foamability at higher foam stabilities was observed.
Key Findings
1
A screening framework evaluated how salinity, pH, surfactant type, and concentration affect foam stability and foam height.
2
At optimum concentration, LA-7 foam stability changed little with salinity, whereas divalent salts—particularly CaCl₂—caused pronounced destabilization effects.
3
Foam stability and foamability showed good correlation at higher foam stabilities, supporting stability-based screening for foam flooding.
4
The highest water recovery in porous-media flooding was achieved using 1 CMC SDS + 0.5 M NaCl, 1 CMC SDS + 0.01 M CaCl₂, and LA-7 at approximately pH 6.
5
The most stable foam increased total water recovery by 65% compared with air-only injection.
Research Object
Foams generated with anionic sodium dodecyl sulfate and nonionic lauric alcohol ethoxylate-7 surfactants for enhanced oil recovery in saline, pH-adjusted conditions and a synthetic porous-medium sand pack
Research Subject
Effects of salinity, pH, surfactant type and concentration on foam stability and foamability, and the resulting water-recovery performance during porous-media flooding
Publication Details
Publication Date
2022-04-19
Journal
Publisher
ISSN
Cited by
75
Open access PDF
Access Type
Author Information
Download PDF
Subscribe to digest
References available in scid.ai3
The use of surfactants in enhanced oil recovery: A review of recent advances2020
The effect of surfactant concentration, salinity, temperature, and pH on surfactant adsorption for chemical enhanced oil recovery: a review2019
Hybrid surfactant-nanoparticles assisted CO2 foam flooding for improved foam stability: A review of principles and applications2021