Deposition rate enhancement in HiPIMS without compromising the ionized fraction of the deposition flux
Повышение скорости осаждения в HiPIMS без снижения доли ионизированной компоненты осаждаемого потока
2013-05-02
SCID: 54.1/4j4u8ebv
Discuss with AI
HiPIMSdeposition rate enhancemention back-attractionionized deposition fluxmagnetic field strength
Figures from the paper
Abstract (AI)
We systematically investigate and quantify different physical phenomena influencing the deposition rate, aD, of Nb coatings prepared by high power impulse magnetron sputtering (HiPIMS), and propose a straightforward approach for deposition rate enhancement through the control of the magnetron's magnetic field. The magnetic field strength at the target surface, B, of a 50?mm diameter magnetron was controlled by the application of paramagnetic spacers with different thicknesses in between the magnetron surface and the target. We found that lowering B achieved by the application of a 2.8?mm thick spacer led to an increase in aD by a factor of ?4.5 (from 10.6 to 45.2?nm?min?1) when the discharge was operated at a fixed average pulse target power density (2.5?kW?cm?2). However, the ionized fraction of the deposition flux onto the substrate was found to be comparable, despite a large difference in B-dependent discharge characteristics (magnetron voltage and discharge current). We show that the decrease in aD commonly observed in HiPIMS (ranging from 33% to 84% in comparison with dc magnetron sputtering in the presented experiments) is governed by different physical processes, depending on the value of B: for high B, the back-attraction of the target ions towards the target is the dominant effect, while for low B the ion back-attraction, the sub-linear dependence of the sputtering yield on the ion energy, and the variation in material transport effects are all important. Finally, we offer a theoretical background for the observed results, demonstrating that the here-presented conclusions may be applicable to HiPIMS discharges using different metal targets and different inert gases.
Key Findings
1
A 2.8 mm paramagnetic spacer lowered the magnetron magnetic field and increased Nb deposition rate approximately 4.5-fold, from 10.6 to 45.2 nm min⁻¹.
2
A theoretical framework explains the observations and suggests that the conclusions may extend to different metal targets and inert gases.
3
At high magnetic fields, target-ion back-attraction dominated deposition-rate reduction; at low fields, back-attraction, sub-linear sputtering-yield dependence on ion energy, and material transport changes jointly contributed.
4
HiPIMS deposition-rate suppression relative to dc magnetron sputtering ranged from 33% to 84% and depended on the magnetic-field strength.
5
The deposition-rate enhancement occurred at fixed average pulse target power density of 2.5 kW cm⁻² without reducing the ionized fraction of the deposition flux.
Research Object
Nb coatings deposited by high power impulse magnetron sputtering (HiPIMS)
Research Subject
Deposition-rate enhancement and the physical mechanisms governing ionized flux transport and deposition-rate reduction as a function of magnetron magnetic-field strength
Publication Details
Publication Date
2013-05-02
Journal
Publisher
ISSN
Cited by
93
Access Type
Author Information
Download PDF
Subscribe to digest
References available in scid.ai2
Cited by6
Plasma diagnostics for understanding the plasma–surface interaction in HiPIMS discharges: a review2014
Industrial application potential of high power impulse magnetron sputtering for wear and corrosion protection coatings2023
Recent progress on high power impulse magnetron sputtering (HiPIMS): The challenges and applications in fabricating VO2 thin film2019
Sideways deposition rate and ionized flux fraction in dc and high power impulse magnetron sputtering2020
Hard AlN films prepared by low duty cycle magnetron sputtering and by other deposition techniques2017
Self‐Lubricating Physical Vapor Deposition Coatings for Dry Cold Massive Forming2019